APC150

APC-150

  • Pneumatic version presussure range -90 to 1000 Kpa
  • Vacuum to -99.9 with optional external vacuum pump
  • Portable type
  • Reduce calibration time 40%
  • Accuration 0.025% FS (optional 0.01% FS)
  • Control Stabillity 0.01%
  • FS Include PC Calibration Software
  • Execute 10 Points Test on a 2000 kpa Transmitter in Minutes!!!
  • Engineering Unit: kPa, Psi, Kg/cm2,Bar, Mpa (depend on range)
  • Pressure connection: 1/8” and 1/4” NPT Female
  • Electrical Input: 4-20 Milli-amp with 24 Vdc Loop Power.

APC300

APC-300

  • Pneumatic version presussure range -90 to 2000 Kpa
  • Reduce calibration time 40%
  • Accuration 0.025% FS (optional 0.01% FS)
  • Control Stabillity 0.01% FS
  • Execute 10 Points Test on a 2000 kpa Transmitter in Minutes!!!
  • Engineering unit: Psi, Kpa, Kg/cm², Bar, mmH2O
  • Pressure Connection: 1/8″ and 1/4″ NPT Female
  • Medial Compatibility: Clean Dry Air
  • Electrical input: 4-20 Milli-amp with Loop Power

AHC Series

AHC-10000

  • Hydraulic version pressure range up to 1000 bar
  • Warm up time 10 minute
  • Reduce calibration time 40%
  • Accuration 0.05% FS (optional 0.025% FS or 0.01% FS 1 year)
  • Engineering unit : Psi, Kpa, Mpa, Kg/cm2, Bar
  • Pressure Connection: 1/2″ and 1/4″ or 3/8″ NPT Female
  • Electrical input: 4-20 Milli-amp with Loop Power
  • Execute 20 Points Test on a 1000 Bar Transmitter in Minutes!!!

HPC Series

HPC-10000

  • Hydraulic version pressure range up to 700 bar or 10000 psi
  • Optional Digital Gauge Range: 100, 300, 500, 1000, 2000, 3000, 5000, 10000 psig
  • Pressure Connection: 1/4″, 3/8″, 1/2″ BSP Female
  • Medial Compatibility: Hydraulic Oil or or Distilled water
  • Material: Brass, Nickel Plated
  • Unit Size: 320x300x250 mm
  • Weight: 9 kg

Digital Pressure Gauge

TIS-PG

  • Material : 316 SS
  • Accuracy : ±0.05% FS Positive pressure, Vacuum/500 psi & below
  • Dimensions 4.375” x 5.0” x 1.50”
  • Bottom Connection ¼” male NPT
  • Display 5 Digit, 0.65”, Bargraph -0 to 100% in 20 segments
  • Power 3 size AA alkaline batteries life 1500 hour w/o backlight
  • Enclosure : NEMA 4, IP65, CSA Intrisically safe Clas 1 Div. 1.

Hand Pump

hand-pump-anim

  • Material : 316 SS
  • Hydraulic Pump 0 to 5000 psi
  • Pneumatic Pump -12.3 to 500 psi

Test Bench WKS Series

testbench-wks-series

  • Pneumatic / Electrical Test Bench
  • Modular Panels to suits user requirements.
  • Typical modules are high pressure section with liquid booster to 6000 psi.
  • Compound section for +/-1 bar with measure and control
  • Low differential pressure section +/-10kPa with measure and control, pressure controller section for -1 to 20 bar.
  • Multi -Function Calibrator
  • Decade boxes and etc.
  • For more information or customization, please contact factory.

Electric Pump Pressure Calibrator

EPC300

epc300

Portable Electric Pump Pressure Calibrator

Pressure Specification

Internal Reference Ranges  -95~3000kPa, -95~2000kPa, -95~1000kPa, -95~700kPa, -95~200kPa
Accuracy  0.025%FS (optional Dual Range, 50% F.S or 0.01%FS)
Pressure Resolution  6 Full Digits
Temperature Compensation  0 to 50 Deg C to rated accuracy
Selectable Engineering Units  Mpa, bar, kg/cm2, kPa, psi, inH20(20/4 C), mmH20(20/4 C), inHg
Time Pressure Generation  0-20 bar < 45 seconds, 0-30 bar < 90 seconds, 0 to -0.95 bar < 5 seconds
Control Stability  +/-0.0005 bar (using manual fine regulator)
Pressure Generation  Built-in eletric pump (self generate), Maximum 30 bar

Optional Electrical Inputs  

mA Input Range  +/- 0 to 24 mA (Switchable internal 24 VDC@55 mA Loop Power)
mA Input Accuracy  0.015%FS
mA Resolution  0.001mA
Volts Input Range  +/- 0 to 30 VDC
Volts Input Accuracy  0.025%FS
Vdc Resolution  0.001Vdc
Switch Input  Non-contact Input

General Specification

Display  L.C.D 128 x 64 dots matrix (with switchable white back-light)
Warm Up Time  5 minutes
Communication  RS232
Optional Vacuum  Up to -99 kPa
Power/Operating Hours  14.8 V Li-ion / 4 hours per charge
Unit Size  315 x 255 x 150 mm
Weight  5 kg

  

EPC600-Basic

epc600-basic

Portable Electric Pump Pressure Calibrator

Pressure Specification    

Internal Reference Ranges  0-7 bar, 0-20 bar, 0-40 bar, 0-70 bar, 0-100 bar
Accuracy  0.05%FS, 0.025%FS or 0.01%FS
Pressure Resolution  5 Full Digits (0.05% / 0.025%FS), 6 Full Digits (0.01% FS)
Temperature Compensation  0 to 50 Deg C to rated accuracy
Selectable Engineering Units
  Mpa, Bar, kg/cm2, kPa, psi, etc
Time Pressure Generation  0-7 bar (<1 min), 0-20 bar (<2 mins), 0-40 bar (<3 mins)
Control Stability  +/-0.001 bar (using manual fine regulator)
Pressure Generation Built-in eletric pump (self generate), Maximum 40 bar Optional 70 Bar & 100 Bar

Optional Electrical Inputs

mA Input Range  0 to 24 mA (24 VDC Loop Power)
mA Input Accuracy  0.015%FS
Volts Input Range  0 to 30 VDC
Volts Input Accuracy
  0.025%FS
Switch Input
 Non-contact Input

General Specification

Warm Up Time  5 minutes
Communication  RS232
Optional Software  Easy Cal (for Pressure Gauge Calibration)
Optional Vacuum  Up to -0.9 Bar or -0.99 Bar
Size  400 x 330 x 170 mm (for <=40 Bar)  l  470 x 357 x 176 mm (for >40 Bar)
Weight  10 kg (for <=40 Bar)                        l  12 kg (for >40 Bar)
Power/Operating Hours
  14.8 V Li-ion / 3 hours per charge

EPC600-Plus

epc600-plus

Electric Pump Pressure Calibrator

Pressure Specification

Internal Reference Ranges  0-7 bar, 0-20 bar, 0-40 bar, 0-70 bar, 0-100 bar
Accuracy  0.05%FS, 0.025%FS or 0.01%FS
Pressure Resolution  5 Full Digits (0.05% / 0.025%FS), 6 Full Digits (0.01% FS)
Temperature Compensation  0 to 50 Deg C to rated accuracy
Selectable Engineering Units
  Mpa, Bar, kg/cm2, kPa, psi, etc
Time Pressure Generation  0-7 bar (<1 min), 0-20 bar (<2 mins), 0-40 bar (<3 mins)
Control Stability  +/-0.001 bar (using manual fine regulator)
Pressure Generation  Built-in eletric pump (self generate), Maximum 40 bar Optional 70 Bar & 100 Bar

Optional Electrical Inputs

mA Input Range  0 to 24 mA (24 VDC Loop Power)
mA Input Accuracy  0.015%FS
Volts Input Range  0 to 30 VDC
Volts Input Accuracy
  0.025%FS
Switch Input  Non-contact Input

General Specification

Display  4.3″ TFT Colour Touch Screen
Warm Up Time  5 minutes
Communication  RS232
Optional Software  Easy Cal (for Pressure Gauge Calibration)
Optional Vacuum  Up to -0.9 Bar or -0.99 Bar
Size  400 x 330 x 170 mm (for <=40 Bar)  l  470 x 357 x 176 mm (for >40 Bar)
Weight  10 kg (for <=40 Bar)      l  12 kg (for >40 Bar)
Power/Operating Hours
  14.8 V Li-ion / 3 hours per charge

EPC600-H

epc600h

Electric Hydraulic Pump Pressure Calibrator

Pressure Specification

Pressure Range
 0~100 bar, 0~200 bar,
 0~400 bar, 0~700 bar
Accuracy  0.05 %FS, 0.025%FS or 0.01%FS
Resolution  5 or 6 Digits
Engineering Units  Mpa, kPa, bar, kg/cm, psi
Pressure Stability  +/- 0.001 bar
Operating Temperature  0 to 50 Deg C

Electrical Specifications

mA Range / Accuracy  0 – 24 mA Loop Powered (without 24 Vdc) / 0.015%FS
Volt Range / Accuracy  0 – 30Vdc / 0.025%FS
Pressure Switch  Non Contact Input

Basic Unit

Display  4.3″ TFT Colour Touch Screen
Warm Up  5 minutes
Communications  RS232
Software (Optional)
 PC based TIS Integrated Calibration Software
 TIS Cal-Ware
Dimension / Weight  400 x 330 x 170 mm / 10 kg

TEMPERATURE CALIBRATION SYSTEM ATCS1200

ATCS1200

Technical Information

Temperature Range

Ambient to 1200 Deg C
 TC  RTD
System Accuracy  +/-1.0 Deg C (300 Deg C – 1200 Deg C)  +/-0.5 Deg C (0 Deg  C – 300 Deg C)
Scanner Accuracy  +/-0.4  +/-0.25
Resolution  0.1 Deg C  0.1 Deg C
Stability (20 to 30mins after normal stablisation)
  Water Bath  +/-0.01 Deg C
  Silicon Oil Bath  +/-0.01 Deg C
  Furnace  +/-0.5 Deg C (Probes & Reference should be tied together & insertion depth about 300mm)
Temperature Uniformity
  Water Bath  +/-0.05 Deg C
  Silicon Oil Bath  +/-0.05 Deg C
  Furnace  +/-0.5 Deg C (Same depth)
Working Volume   l Dimension  l  Weight
  Water Bath  Diameter: 75mm x 300mm  l  360 x 300 x 300mm  l 20kg
  Silicon Oil Bath  Diameter: 75mm x 300mm  l  220 x 460 x 610mm  l 20kg

  Furnace

 Diameter: 65mm x 300mm  l  525 x 360 x   775mm  l  32kg

Standard Accessories:

1) Factory Calibration Certificate for Scanner & Reference Probe tracable to National Standard
2) Operating Manual
3) TIS Temp. Cal-ware (software)
4) PT100 Class A Reference Probe (*For Model ATCS1200-W-S)
5) Typed S Class A Reference Probe (*For Model ATCS1200-F)
6) Type J,K,T,E extension wires x 12 pieces (2m each)
7) PT100 extension 4-wires x 12 pieces (2m each)
8) Power Cord

TACHOMETER CALIBRATOR RPM SERIES

Specifications of RPM Series
Speed/Velocity Contact  0-6000 rpm / 0-12,000 rpm
Speed/Velocity Non-Contact  0-60,000 rpm / 0-100,000 rpm
Uncertainties  +/-0.1 rpm below 1000 rpm, +/-1.0 rpm above 1000 rpm
Resolution  0.1 rpm (<1000 rpm), 1 rpm (>=1000 rpm)
Shaft Rotation  Clockwise or Anti-Clockwise
Stable Time  < 5 seconds
Motor Type  Ultra-Stable Servo Motor, 4000 counts encoder/Controller Direct Drive Shaft      (without gear)
Noise Level @ 1 meter  < 50 dB
Supply  240 VAC, 50/60Hz @ 4 Amp
Display  4.3″ TFT Colour Touch Screen
Unit Size  420 x 350 x 250 mm
Weight  12 kg

FIELD BUS POWER SUPPLY TIS-FBPS

TIS FBPS

Field Bus Power
Battery operated to output 24VDC to Power Transmitter or Valves Impedance Matching for Field Bus 
Able to power up 1 segment Field Bus device
Can be configure to power up H.A.R.T. device, with impedance matching